Manufacturer
203 recalls in our database name Altec Industries, Inc. as the manufacturing or recalling firm.
Of the 203 recalls from Altec Industries, Inc. we have scored against our rubric, 3 (1%) are Critical — deaths or serious injuries reported, or the agency’s own highest classification — and 108 (53%) are Severe.
The manufacturer string comes from the agency’s own source notice — for FDA recalls, the “recalling firm” field; for NHTSA recalls, the vehicle manufacturer; for CPSC recalls, the firm-of-record on the joint press release. A single corporate family can appear under multiple manufacturer strings as agency notices aren’t standardized on a canonical name. If you don’t see recalls you expect, try a parent-company search or a broader full-text search.
Severity scores below are computed from the agency’s classification and the recall text, never from manufacturer behaviour or history. Many manufacturers issue routine corrective actions (software updates, labelling corrections) that are correctly scored low — having recalls on this list isn’t inherently a quality signal.
Altec is recalling 2014-2021 TDA-58 aerial devices because transport tie-down chains may break, increasing crash risk.
Altec is recalling 2017-2018 aerial devices because rotation bearing fasteners may crack and break, potentially causing the pedestal and turntable to separate.
Altec is recalling 2017-2019 DC1317 and DRM12 wood chippers because a flexible exhaust pipe section may separate, creating an exhaust gas leak that increases the risk of a fire.
Altec is recalling 2017-2020 DT65-E and DT65-H vehicles because the capacity placard location creates a pinch point that could injure operators.
Altec is recalling 213 digger derricks from 2016-2020 that lack the required combined use capacity chart, posing an injury risk to operators.
Altec is recalling 2020 AN67-E100 aerial devices because a shuttle cartridge was installed instead of a plug, risking unintended boom movement and injury.
Altec is recalling 2018-2020 digger derricks and aerial devices because a hydraulic check valve snap ring can fail, causing unintended boom movement.
Altec is recalling 2006-2020 AH150 and AH125 aerial devices because an incorrect counterbalance valve may cause the boom to lower unexpectedly, increasing injury risk.
Altec is recalling 280 units of 2019-2020 aerial devices and digger derricks because bolts securing the pedestal to the turntable may fail, posing a risk of injury or death.
Altec is recalling 2018-2020 EC505 and EC655 vehicles because grapple tines may loosen, risking loss of load control.
Altec is recalling 2015-2018 aerial devices because a software issue can cause the boom to move unexpectedly during an engine cycle, increasing injury risk.
Altec Industries is recalling 1995-1998 A0442 aerial devices because a hydraulic cylinder end gland may fail, causing uncontrolled boom movement and increasing injury risk.
Altec is recalling 2017-2020 aerial devices due to a power take-off that may leak oil onto the exhaust heat shield, increasing fire risk.
Altec is recalling 2014-2020 Aerial Devices with Class 3 towing hitches that may have incorrect load ratings or damage from overloading, increasing crash risk.
Altec is recalling 2018-2020 aerial devices and digger derricks because bolts securing the pedestal to the turntable may fail, increasing the risk of injury or death.
Altec is recalling 92 ST Spray Trucks from 2017-2020 because an improperly mounted battery fuse holder may cause an electrical short circuit and fire.
Altec is recalling 2016-2018 AT200A vehicles because incorrect rear tire markings may cause overloading, increasing crash risk.
Altec is recalling 2019-2020 Digger Derricks because operators may inadvertently open the pole guide, risking loss of load control and injury.
Altec Industries is recalling 238 specific 2019 aerial devices because high-strength fasteners securing the pedestal to the turntable may fail, potentially causing the pedestal to separate.
Altec is recalling 2015-2019 AC26, AC28, AC30, and AC38 crane aerial devices because a boom lift cylinder hose may lack a velocity fuse, risking uncontrolled movement.
Altec Industries is recalling 2018-2019 aerial devices that were not stability tested according to ANSI A92.2 standards, posing a risk of collapse.
Altec is recalling 2016-2019 Digger Derrick vehicles because incorrectly plumbed outrigger valves may cause the unit to retract unexpectedly, risking collapse and injury.
Altec Industries is recalling 2019 LR7-Series aerial devices because the trailer brake controller may be improperly grounded, increasing crash risk.
Altec is recalling 2012-2019 aerial devices because a winch valve defect may allow lifting beyond rated capacity, increasing injury risk.
Altec Industries is recalling 2018-2019 aerial devices because high-strength fasteners may fail, potentially causing the pedestal to separate from the turntable.
Community-sourced company facts from Wikidata, not from any recall agency. This is background on the corporate entity — it says nothing about the recall(s) listed on this page, which come from the agency source notice above.
ALTEC
company in the Czech Republic
Source: Wikidata (Q54941310), licensed CC0. Wikidata is community-edited and may not reflect the current corporate structure.